Gary Sroka

Report of the Condition of a General Electric Transportation Systems Gearbox

Posted by on Dienstag, April 14th, 2020 in

Wind power plant operation and maintenance (O&M) costs remain an appreciable contributor to the overall cost of wind energy, with a capacity-weighted average of $11/megawatt-hour (MWh) for projects installed since 2000 and $9/MWh for projects install...

View More

Gear Corrosion During the Manufacturing Process

Posted by on Dienstag, November 19th, 2013 in

No matter how well gears are designed and manufactured, gear corrosion can occur that may easily result in catastrophic failure. Since corrosion is sporadic and a rare event and often difficult to observe in the root fillet region or in finely pitche...

View More

High Speed, Automatable Superfinishing of Rear-Axle Hypoid Gears

Posted by on Dienstag, November 19th, 2013 in

The benefits gained by superfinishing rear-axle hypoid gearsets are now well documented. Friction, wear and operating temperature are significantly reduced. The main impediment to commercially implementing this process, however, is that it increases ...

View More

A Novel Approach to the Refurbishment of Wind Turbine Gears

Posted by on Mittwoch, November 13th, 2013 in

Multi-megawatt wind turbine gearboxes operate under demanding environmental conditions including considerable variation in temperature, wind speed, and air quality....

View More

The Impact of Surface Condition and Lubricant on Gear Tooth Friction

Posted by on Donnerstag, November 6th, 2014 in

Frictional losses in gear boxes are of significant interest to gear box designers as these losses transform into heat.  The direct result is a reduction in the fuel efficiency of the vehicle involved....

View More

An Evaluation of the New Rapid ISF® Process for Real-Axle Gears

Posted by on Montag, Juni 2nd, 2014 in

REM ist der Technologieführer im Bereich der Oberflächenbearbeitung von Metallteilen. Als solcher verfügen wir über zahlreiche Fachartikel und Ressourcen zu […]...

View More

Superfinishing Rear Axle Gears – A Significant Step Toward Reducing Automotive Greenhouse Gas Emissions

Posted by on Montag, Juni 2nd, 2014 in

REM ist der Technologieführer im Bereich der Oberflächenbearbeitung von Metallteilen. Als solcher verfügen wir über zahlreiche Fachartikel und Ressourcen zu […]...

View More

Comparative Corrosion Characteristics of Ground and Superfinished Gear Steels

Posted by on Montag, Juni 2nd, 2014 in

REM ist der Technologieführer im Bereich der Oberflächenbearbeitung von Metallteilen. Als solcher verfügen wir über zahlreiche Fachartikel und Ressourcen zu […]...

View More

The Effect of the Surface Roughness Profile on Micropitting

Posted by on Montag, Juni 2nd, 2014 in

REM ist der Technologieführer im Bereich der Oberflächenbearbeitung von Metallteilen. Als solcher verfügen wir über zahlreiche Fachartikel und Ressourcen zu […]...

View More

High Speed, Automatable Superfinishing of Rear-Axle Hypoid Gears

Posted by on Montag, Juni 2nd, 2014 in

REM ist der Technologieführer im Bereich der Oberflächenbearbeitung von Metallteilen. Als solcher verfügen wir über zahlreiche Fachartikel und Ressourcen zu […]...

View More

A Novel Approach to the Refurbishment of Wind Turbine Gears

Posted by on Montag, Juni 2nd, 2014 in

REM ist der Technologieführer im Bereich der Oberflächenbearbeitung von Metallteilen. Als solcher verfügen wir über zahlreiche Fachartikel und Ressourcen zu […]...

View More

Gear Corrosion During the Manufacturing Process

Posted by on Montag, Juni 2nd, 2014 in

REM ist der Technologieführer im Bereich der Oberflächenbearbeitung von Metallteilen. Als solcher verfügen wir über zahlreiche Fachartikel und Ressourcen zu […]...

View More